Rotary Dryer | Vacuum Dryer | Double Cone Dryer
Official ⎝⎛体育滚球平台⎞⎠ | Sitemap |
Company: Changzhou Lima Drying Technology Co., Ltd.
Contact: Zhou Youlai 13806118222
Phone: 0519-88968880
Fax: 0519-88968686
Mobile: 13806118222 18136711288
Address of Company: No. 11 Jinhua Road, Wujin District, Changzhou City, Jiangsu Province
Product Categories
company ⎝⎛体育滚球平台⎞⎠

Double cone rotary vacuum dryer

  • Product name: Double cone rotary vacuum dryer
  • Product model: SZG
Product details:

Working principle SZG double cone rotary vacuum dryer is a double cone rotary tank. Under the vacuum state, the tank is heated by passing thermal oil or hot water into the jacket, and the heat contacts the wet material through the inner wall of the tank. The water vapor or other gas evaporated after the wet material absorbs heat is sucked away by the vacuum pump through the vacuum exhaust pipe. Because the inside of the tank is in a vacuum state, and the rotation of the tank keeps the material up and down, turning inside and out, it speeds up the drying speed of the material, increases the drying rate, and achieves the purpose of uniform drying.

Features The double cone rotary vacuum dryer is a new type of dryer integrating mixing and drying. The condenser, vacuum pump and dryer are matched to form a vacuum drying device. (If the solvent does not need to be recovered, the condenser may not be used.) This machine has advanced design, simple internal structure, easy cleaning, all materials can be discharged, and the operation is simple. Can reduce labor intensity and improve working environment. At the same time, the material also rotates when the container itself rotates, but no material accumulates on the wall, so the heat transfer coefficient is high and the drying rate is large, which not only saves energy, but also the material is evenly and fully dried and has good quality. Can be widely used in pharmaceutical, chemical, food, dyeing and other industries.

Scope of application This machine is suitable for vacuum drying and mixing of powder and granular materials in the pharmaceutical, food, chemical and other industries, especially for the following requirements:
※ High temperature sensitive materials cannot be accepted ※ Materials that need to recover solvents and toxic gases ※ Materials that are easy to be oxidized and dangerous ※ Materials that require crystals ※ Materials that require extremely low residual volatile content

Technical specifications

name

model

100

350

500

750

1000

1500

2000

3500

4500

5000

Tank inner volume (L)

100

350

500

750

1000

15000

2000

3500

4500

5000

Maximum loading volume (L)

40

140

200

300

400

600

800

1400

1800

2000

Loading weight (kg)

20

70

100

150

200

300

400

700

900

1000

Speed (rpm)

3 ~ 13

6

5

4

4

4

Motor power (kw)

0.75

1.1

1.5

2.2

3

4

5.5

7.5

11

15

Floor area (mm)

2160
× 800

2160
× 800

2350
× 800

2560
× 1000

2860 ×
1300

3060
× 1300

3260
× 1400

3760
× 1800

3960
× 200

4400
× 2500

Swing height (mm)

1750

2100

2250

2490

2800

2940

2990

3490

4100

4200

Design pressure in tank (MPa)

-0.1 ~ 0.15

Jacket design pressure (MPa)

≤0.3

Weight (kg)

800

1100

1200

1500

2800

3300

3600

6400

7500

8600

Note: For materials with large volume changes before and after drying, the loading factor can be appropriately increased or decreased, and the maximum loading volume cannot contact the bottom surface of the vacuum tube.
The motor can be equipped with a speed-adjusting motor according to the user's requirements, and the speed is 0 ~ 6rpm. The above technical parameters are calculated according to 0.6g / c m3. If the liner material is glass-lined, it must be presented when ordering; if the material is flammable and explosive, it must be clearly stated when ordering, otherwise it is strictly prohibited.
download Google
※ The heating is divided into hot water and heat transfer oil.
※ When ordering, please indicate the temperature that the material can withstand or the temperature of the dryer, so that the factory can choose or provide you with a heat source.
※ When drying viscous materials, our factory will specially design a "copy board" structure in the tank.
※ The accessories involved in the vacuum drying system can be provided and installed by users in our factory, please specify in the order.
※ Our factory can provide design, manufacture and installation for the special requirements of users.

Previous: Pressure spray dryer
Next: Belt vacuum dryer
share to:

QR code for mobile station


Scan and add WeChat
欢乐拼三张 星力捕鱼 龙博线上娱乐 七乐彩